WE DO A JOB WITH EVERY TOOL BEFORE OFFERING IT FOR RENT
To Ensure You Get the Best Tool for the Job!
WE COMPLIED A LIST OF TIPS AND TRICKS FOR MOST OF THE TOOLS IN OUR INVENTORY!
CARPET CLEANER
- ALLOW THE CARPET SOLUTION TO SOAK UP GRIME AND DIRT FOR 30 MINUTES BEFORE USE
- VACUUM THE AREA BEFORE USE TO REMOVE ANY HAIR FROM THE CARPET
- USE THE WAND ATTACHMENT FOR THE CORNER CASES.
- USE WARM WATER WITH YOUR CARPET SOLUTION.
CONCRETE SAW 14 INCHES
MY RECOMMENDATIONS ARE :
- USE HEARING PROTECTION AS THE MACHINE IS EXTREMELY LOUD.
- SPRAY WATER ON THE BLADE WHILE ITS CUTTING TO REDUCE DUST
- WHEN CUTTING THROUGH A WALL ALLOW THE BLADE THE REACH FULL RPM'S BEFORE MAKING YOUR NEXT CUT, AN EXAMPLE WOULD BE ON A VERTICAL SURFACE, ONCE THE BLADE IS INSERTED INTO THE WALL, ALLOW IT TO REACH FULL RPMS THEN PUSH DOWNWARDS, REPEAT THIS PROCESS MULTIPLE TIMES, THIS AVOIDS THE BLADE GETTING JAMMED IN THE MASONARY.
12*18 FLOOR SANDER
- START OFF WITH AN AGGRESSIVE GRIT (20 OR 36 GRIT) TO REMOVE JUNK OFF THE WOOD
- ALLOW THE SANDER TO MOVE WHERE IT WISHES, THIS IS ALLOWING IT TO LEVEL THE WOOD AND FIX IMPERFECTIONS.
- USE A HIGHER GRIT TO GIVE THE WOOD A FINAL POLISH( 80 OR 100 GRIT)
16 INCH COMPACTOR
- THE COMPACTOR MOVES IN A FORWARD MOTION, DONT TRY TO FORCE IT BACKWARDS.
- PLACE FROM REVERSE PRESSURE ON THE COMPACTOR, THIS ALLOW'S IT TO STAY IN PLACE AND FULLY COMPACT THE GROUND BELOW.
- USE THE WATER TANK ON ASPHALT WORK TO ADD WEIGHT TO THE MACHINE THIS ALWAYS FOR BETTER COMPACTION.
SCL1000 LOADER
- THE SCL1000 WORKS THE SAME WAY AS THE TORO DINGO.
- THE DIFFERENCE BEING THE SCL1000 HAS BOTH THE OPERATORS PLATFORM AND ENGINE PLACEMENT IN THE REAR. WITH AN EMPTY BUCKET OVER UNEVEN TERRAIN THIS CAN CAUSE BALANCE ISSUES. AN OPERATOR HAS TO ALWAYS KEEP IN MIND THE MACHINES WEIGHT DISTRIBUTION
- IT IS GENERALLY RECOMEND A NEW OPERATOR USES A TORO DINGO FIRST DUE TO ITS MORE BALANCED WEIGHT DISTRIBUTION.
NOTE: IF MACHINE IS TIPPED OVER TURN OFF ENGINE IMMEDIATELY AND CALL US, THE ENGINE MUST GET ITS OIL CHANGED TO AVOID A BENT PISTON ROD WHICH IS AN EXPENSIVE REPAIR.
TORO DINGO LOADER
- THE TORO DINGO IS POWERED BY HYDRALICS, INCREASING ENGINE THROTLE ALLOWS ITS HYDRALIC FLUID TO FLOW FASTER ALLOWING IT TO DO MOST TASKS QUICKER.
- THE DINGO USES TRACKS THE MOVE, WHEN TURNING ONE TRACK STOPS MOVING WHILE ANOTHER MOVES, ALLOW FOR WIDER TURNS TO AVOID DAMAGE TO GRASS.
- WHEN OPERATING HEAVY MACHINERY, AN OPERATOR HAS TO ALWAYS KEEP IN MIND WEIGHT DISTRIBUTION, THE DINGOS ENGINE PLACEMENT IS IN THE MIDDLE OF ITS FRAME WITH THE BUCKET AT THE END. WHEN THE BUCKET IS FULL IT ADDS WEIGHT TO THE FRONT END, WHEN GOING OVER UNEVEN SURFACES ALWAYS KEEP THE BUCKET LOW TO THE GROUND TO AVOID A TIP OVER.
NOTE: IF MACHINE IS TIPPED OVER TURN OFF ENGINE IMMEDIATELY AND CALL US, THE ENGINE MUST GET ITS OIL CHANGED TO AVOID A BENT PISTON ROD WHICH IS AN EXPENSIVE REPAIR.
DUMP TRAILER 5*10
- THE DUMP TRAILER HAS A CAPACITY OF 3500 LBS.
- DO NOT USE LARGE MACHINERY TO UNLOAD THE DUMP TRAILER, THIS CAN CAUSE A TIPOVER.
- USE THE TRAILER COVER TO PREVENT SPILLOFFS.
1 MAN AUGER
- THE 1 MAN AUGER HAS A 6 AND 8 INCH BIT FOR 4 FEET DEPTH
- THE 1 MAN AUGER CANNOT HANDLE ROCKS OR ROOTS, IN GENERAL THE OTTAWA AREA IS HARD TO TELL WHAT WILL BE UNDER THE GROUND
- DO NOT DISENGAGE THE TROTTLE ONCE YOU REACH THE REQUIRED DEPTH, USE THE THROTTLE TO HELP LIFT THE MACHINE UP
BX23S BACKHOE
- THE BX23S HAS AN OPERATOR SEAT TO SIT ON WHILE IN USE, THE OPERATOR SEAT HAS A SENSOR WITHIN IT TO SENSE WEIGHT, IF THE SENSOR DOSENT DETECT WEIGHT, THE MACHINE WILL NOT MOVE, ENSURE YOU ARE WEARING YOUR SEATBELT TO ALLOW FOR YOUR FULL WEIGHT TO BE IN THE SEAT.
- THE BACKHOE ON THE BX23S CAN GO TO A DEPTH OF 6 FEET AND 1 INCH.
- USE THE HORIZONTAL STABILIZERS ON THE MACHINE TO HELP WITH STABILITY WHEN TRENCHING
- THE BACKHOE PLATFORM CAN BE REMOVED FOR TIGHT CORNERS, CONTACT US AND WE WILL COME HELP.
NOTE: IF MACHINE IS TIPPED OVER TURN OFF ENGINE IMMIDENTELY AND CALL US, THE ENGINE MUST GET ITS OIL CHANGED TO AVOID A BENT PISTON ROD WHICH IS AN EXPENSIVE REPAIR.
SDS MAX/PLUS BITS AND DRILLS
- TO ENSURE YOUR TAPCON BOLTS OR CARRIAGE BOLTS ENTER MASONARY PROPERLY, VACUUM THE HOLE AFTER DRILLING.
- USE THE HAMMER+ ROTARY FUNCTION TO GET QUICK WORK DONE
- IF YOU ENCOUNTER REBAR, TURN THE MACHINE TO ROTARY FUNCTION ONLY, THE HAMMER FUNCTION COULD END UP JAMMING THE BIT.
CHAINSAWS + POWER PRUNER
- EVERY CHAINSAW OR POWER PRUNER GOES OUT WITH A NEW BLADE, WHEN IN USE, THE BLADE WILL LOSSEN, USE THE TOOL PROVIDED TO YOU TO TIGHTEN THE CHAIN.
- AS CHAINSAWS ARE 2 STROKE ENGINES, THEY ARE PRONE TO ENGINE FLOODING, IF THE MACHINE WILL NOT KICK ON AFTER USING CHOKE AND THROTTLE. ALLOW THE MACHINE TO SIT FOR 30 MINUTES, THIS ALLOWS FOR THE OIL IN THE CYLINDER TO DISEPATE.
CHECK OUT OUR RENTAL INVENTORY!
Your Dynamic Snippet will be displayed here... This message is displayed because you did not provided both a filter and a template to use.